石灰干化污泥稳定后土壤中Pb、Cd和Zn浸出行为的研究

以人工制备Zn、Pb、Cd污染土壤为研究对象,采用城市污水处理石灰干化污泥作为稳定剂,对污染土壤进行稳定化处理,并采用TCLP、SPLP、去离子水浸提和优化的BCR连续提取法对稳定化效果进行分析和评价.结果表明,单独使用石灰干化污泥,TCLP浸出浓度随着干化污泥质量分数的增加而显著减少,干化污泥的质量分数为40%时,稳定化率最大为Zn-99.54%、Pb-99.60%、Cd-99.85%.SPLP和去离子水浸出评价稳定效果时,Pb和Zn在加入质量分数10%和20%的干化污泥时浸出明显降低,但在加入30%和40%时由于在强碱条件Pb和Zn会再溶出,导致稳定效果变差.为了恢复植物生长功能,经过FeSO4和H3PO4调节pH后,石灰干化污泥稳定过的土壤pH有效降低,同时FeSO4和H3PO4有利于促进Pb和Zn的稳定效果.经稳定化后,土壤中的重金属可交换态降低,限制了土壤重金属的迁移.该研究结果表明石灰干化污泥可以再利用,应用于重金属污染土壤的稳定化修复中,并能改善稳定后土壤适宜植物生长的理化性质.     

不同施磷量(KH2PO4)作用对Cu、Zn在红壤中的迁移转化

为了比较不同施磷量对土壤中重金属Cu、Zn迁移转化的影响,采用土壤柱进行室内淋溶实验,研究常见的磷肥磷酸二氢钾在少量5 mg·kg-1,适量15 mg·kg-1以及过量25 mg·kg-1条件下对Cu、Zn在红壤中的淋溶效应.结果表明土壤施用磷酸二氢钾降低了土壤渗滤液的pH,不同施磷量对土壤渗滤液pH影响不大,在整个淋滤过程,渗滤液pH呈现上升的趋势.磷酸盐作用下重金属Cu在土壤中的迁移主要集中表层土壤中,而Zn逐渐向深层土壤中迁移.土壤深层渗滤液中Cu、Zn浓度均比较低,对浅层地下水的危害性不大.淋滤结束后,重金属主要以残渣态存在土壤中,重金属Cu残渣态的比例为60%左右,重金属Zn残渣态比例为40%左右.高浓度磷酸二氢钾作用下有利于重金属Zn从残渣态及有机结合态向交换态转化.     

不同条件下皂苷对污染塿土中Cu、Pb的淋洗修复

为了探讨环境友好型生物表面活性剂皂苷(saponin)对污染塿土中重金属Cu、Pb的淋洗修复效果,采用批次试验方法,研究了皂苷在不同的淋洗时间、质量浓度、p H、淋洗次数及背景电解质强度下对Cu、Pb单一污染塿土和复合污染塿土中Cu、Pb的淋洗效果.结果表明,当皂苷质量浓度为50 g·L-1、p H值为5.0、淋洗时间为240 min、无背景电解质离子共存时,重金属离子通过与皂苷胶团络合,对污染塿土中Cu、Pb的淋洗去除效果达到最大;在单一污染塿土和复合污染塿土中,50g·L-1的皂苷在最佳淋洗条件下对Cu的单次淋洗百分率分别为29.02%和25.09%,对Pb的单次淋洗百分率分别为31.56%和28.03%,同时也显示皂苷对Pb的去除效果比Cu更显著.经过4次淋洗后,在单一污染塿土和复合污染塿土中皂苷对Cu的累积淋洗百分率分别为58.92%和53.11%,对Pb的累积淋洗百分率分别为77.69%和65.32%.单次淋洗前后污染塿土中重金属形态分级结果表明:污染塿土中吸附态、交换态Cu、Pb的质量分数有所增加;碳酸盐结合态、有机结合态和硫化物残渣态的Cu、Pb可得到有效去除.     

覆膜与降雨类型对土壤水分及NO3--N淋失的影响

在丹江口库区青塘河五龙池小流域,以黄棕壤横垄种植玉米为例,设置覆膜与无覆膜两种处理,采用田间小区实验研究覆膜与降雨类型对0~30 cm土壤水分和NO-3-N淋失的影响.结果表明:两处理土壤含水量均随土层加深而增加,与无覆膜相比覆膜可降低0~10、10~20、20~30cm土层中的含水量.不同降雨类型对覆膜土壤含水量的影响有区别,小雨时3层土壤间差异显著,含水量随土层加深急剧增加;中雨时10~20cm比0~10 cm、20~30 cm比10~20 cm分别高50.80%、6.62%,0~10 cm土壤含水量显著低于10~20 cm和20~30 cm;暴雨时含水量随土层加深增幅变小;覆膜土壤土层越深土壤含水量受降雨的影响越小.覆膜可降低0~10、10~20 cm土层中的NO-3-N淋失量,分别降低40.74%、24.48%,但会增加20~30 cm的淋失;两处理土壤NO-3-N淋失量均随土层加深而增加.不同降雨类型对覆膜土壤NO-3-N淋失的影响也有区别,小雨时随土壤深度的增加淋失量增多;中雨时,0~10、20~30 cm NO-3-N淋失量分别为10~20 cm的1.75、8.41倍;暴雨时,0~10、20~30 cm分别比10~20 cm低18.97%和60.69%.土壤中NO-3-N淋失受土壤含水量的影响,且随土层加深含水量对NO-3-N淋失的影响减弱.     

离子液体对废旧印刷线路板中铜、锌、铅的浸出规律

以离子液体1-丁基磺酸-3-甲基咪唑三氟甲烷磺酸盐([BSO_3HMIm]OTf)为浸出剂,初步研究了WPCBs浸铜过程中锌和铅浸出率的影响因素。实验结果表明:铜、锌的浸出率随着WPCBs粒径的减小、H_2O_2溶液加入量的增大而增大,铜的浸出率随浸出温度的升高先增大后减小,锌的浸出率受浸出温度影响不大;铅的浸出率受5种因素影响不大,且总体处于较低水平。在WPCBs粒径为0.100~0.250 mm、离子液体加入量为60.0%(φ)、H_2O_2溶液加入量为7.5%(φ)、固液比为1∶15、浸出温度为50℃的条件下,铜、锌、铅的浸出率分别为99.84%,93.25%,22.46%。     

Thioarsenate formation upon dissolution of orpiment and arsenopyrite

Thioarsenates were previously determined as dominant species in geothermal and mineral waters with excess sulfide. Here, we used batch leaching experiments to determine their formation upon weathering or industrial leaching of the arsenic-sulfide minerals orpiment (As₂S₃) and arsenopyrite (FeAsS) under different pH and oxygen conditions. Under acidic conditions, as expected based on their known kinetic instability at low pH, no thioarsenates formed in either of the two mineral systems. Under neutral to alkaline conditions, orpiment dissolution yielded mono-, di- and trithioarsenate which accounted for up to 43-55% of total arsenic. Thioarsenate formation upon arsenopyrite dissolution was low at neutral (4%) but significant at alkaline pH, especially under suboxic to sulfidic conditions (20-43%, mainly as monothioarsenate). In contrast to orpiment, we postulate that recombination of arsenite and sulfide in solution is of minor importance for monothioarsenate formation during alkaline arsenopyrite dissolution. We propose instead that hydroxyl physisorption lead to formation of As-OH-S surface complexes by transposition of hydroxyl anions to arsenic or iron sites. Concurrently formed ironhydroxides could provide re-sorption sites for the freshly released monothioarsenate. However, sorption experiments with goethite showed slower sorption kinetics of monothioarsenate compared to arsenite, but comparable with arsenate. The discovery that thioarsenates are released by natural weathering and industrial leaching processes and that, once they are released, have a higher mobility than the commonly-investigated species arsenite and arsenate requires future studies to consider them when assessing arsenic release in sulfidic natural or mining-impacted environments.     

Advantages and risks of using steel slag in preparing composts from raw organic waste

It had been reported that iron and manganese oxides in steel slag enhanced the production of humic acid (HA) from low-molecular-weight compounds, such as phenolic acids, amino acids, and saccharides. In the present study, this function of steel slag was applied to the composting of raw organic wastes (ROWs). The degree of humification of HAs is an important factor in evaluating compost quality. Thus, HAs were extracted from the prepared composts and the humification parameters were determined, in terms of elemental compositions, acidic functional group contents, molecular weights, spectroscopic parameters from UV–vis absorption and ¹³C NMR spectra. The timing for adding steel slag affected the degree of humification of HAs in the composts. The weight average molecular weight of a HA when slag was added initially (29 kDa) was significantly higher than when slag was added after elevating the temperature of the compost pile (17–18 kDa). These results show that ROWs are decomposed to low-molecular-weight compounds after the pile temperature is elevated and the presence of slag enhances the polycondensation of these compounds to produce HAs with a higher degree of humification. Because the slag used in the present study contained several-tens ng g^?1 to several μg g^?1 of toxic elements (B, Cu, Cr, and Zn), leaching tests for these elements from the prepared composts were carried out. Levels for leaching boron from composts prepared by adding slag (0.2–0.4 mg L^?1) were obviously higher than the corresponding levels without slag (0.05 mg L^?1).     

有机酸土柱淋洗法修复重金属污染土壤

通过室内模拟实验,采用土柱淋洗方法,研究草酸、柠檬酸、乙酸和酒石酸溶液对某电镀厂附近土壤中重金属的去除效果。探讨了淋洗剂浓度、淋洗次数和淋洗时间等对淋洗效果的影响,研究草酸淋洗前后土壤中重金属形态的变化。结果表明,淋洗过程中铬的去除效果明显滞后于铜、锌和镍3种重金属离子。1 mol/L的草酸在土水比为1∶1,淋洗5h,淋洗4次的条件下可以达到最佳淋洗效果,Cu、Zn、Ni和Cr的去除率分别是99.6%、66.98%、88.7%和18.23%。     

铬渣秸秆共热解产物铬稳定性研究

生物质铬渣共热解工艺是新型的铬渣处理工艺,该工艺能有效地将铬渣中的Cr(Ⅵ)还原为Cr(Ⅲ).而由于共热解产物总铬含量较高,因此考察了铬渣与秸秆共热解过程中铬稳定性.通过考察共热解产物成分及形态分析、pH影响实验、淋洗实验及长期稳定性实验,对共热解铬渣的铬环境安全性进行评估.结果表明:(1)共热解温度对铬渣形态有较大影响,可交换态及碳酸盐结合态铬含量随共热解温度升高而逐渐降低,800℃时候可交换态铬降至＜0.1％(质量分数,下同),碳酸盐结合态铬为1.2％;共热解后最稳定的残渣态铬含量随共热解温度升高而逐渐升高.(2)当pH＞7时,两种共热解产物总铬溶出量极低,基本都小于6mg/kg;当pH≤7时,总铬的溶出量显著增加,最高超过500 mg/kg.但由于解毒铬渣的酸中和能力极强,因此铬释放风险较低.(3)共热解产物的总铬累积溶出量极低,根据拟合结果计算出其100年填埋时间的总铬溶出量不超过1.3 mg/kg.长期稳定性实验表明,自然堆置过程中共热解产物的Cr(Ⅵ)含量逐渐降低.     

废弃印刷线路板碘化法浸金研究

针对碘化法从废弃印刷线路板中提取金的工艺设计，分别考察了碘的质量分数、n(I₂)/n(I^-)比值、固液比、双氧水的质量分数、pH值、浸出时间和浸出温度对金浸出率的影响。结合正交设计优化实验方法,提出了从废弃印刷线路板中碘化法浸取金的最佳工艺条件：碘的质量分数为1.1％，n(I₂)∶n(I^-)=1∶10，双氧水的质量分数为1.5％，浸出时间4 h，固液比为1∶10，浸出温度为常温（25℃），溶液pH值为中性，此时金浸出率可达97.5％。